By default, all of the client components of Pulp will require validly signed SSL certificates from the servers on remote ends of its outbound connections. On a brand new httpd installation, a self-signed certificate will be generated for the server to use to serve Pulp. This means that a fresh installation will experience client errors similar to this:
(pulp)[rbarlow@coconut pulp]$ pulp-admin puppet repo list +----------------------------------------------------------------------+ Puppet Repositories +----------------------------------------------------------------------+ WARNING: The server's SSL certificate is untrusted! The server's SSL certificate was not signed by a trusted authority. This could be due to a man-in-the-middle attack, or it could be that the Pulp server needs to have its certificate signed by a trusted authority. If you are willing to accept the associated risks, you can set verify_ssl to False in the client config's [server] section to disable this check.
You have two choices to solve this issue: You may make or acquire signed SSL certificates for httpd to use to serve Pulp, or you may configure Pulp’s various clients not to perform SSL signature validation.
If you wish to use signed certificates, you must decide whether you will purchase signed certificates from a root certificate authority or use your own organization’s certificate authority. How to make or buy signed certificates is outside the scope of this document. We will assume that you have these items:
A PEM-encoded X.509 certificate file, signed by a trusted certificate authority.
A PEM-encoded private key file that corresponds to your SSL certificate.
The CA certificate that signed your SSL certificate. This is only necessary if your Linux distribution does not already include the CA that signed your certificate in its system CA pack.
You must first configure httpd to use the SSL certificate and private key you have acquired. You
must configure the SSLCertificateFile and SSLCertificateKeyFile mod_ssl directives to point at
these files. On Red Hat based systems, these settings can be found in
If you are using a CA certificate that is not already trusted by your operating system’s system CA pack, you may either configure Pulp to trust that CA, or you may configure your operating system to trust that CA.
Pulp has a setting called
ca_path in these files:
/etc/pulp/nodes.conf. This setting indicates which CA
pack each of these components should use when validating Pulp server certificates. By default, Pulp
will use the operating system’s CA pack. If you wish, you may adjust this setting to point to a
different CA pack. The CA pack may be a single file that contains multiple concatenated
certificates, or it may be a directory with OpenSSL style hashed symlinks pointing at CA certificate
files, with one certificate per file. Of course, if you have exactly one CA certificate, you can
configure this setting to point at it directly.
There are three settings in
/etc/pulp/server.conf that you should be aware of, but probably
should not alter.
cakey point to a CA certificate and key that Pulp uses to sign
client authentication certificates. Note that this is not the CA that you signed your server
certificate with earlier. It is used only internally by Pulp and Apache to create client
certificates with login calls, and to validate those certificates when clients use the API. It is
best to avoid altering these settings. The third setting is confusingly named
ssl_ca_certificate. This setting should not be used, since it causes a chicken and egg situation
that could cause the universe to experience a machine check exception. If it is configured, the yum
consumer handlers will use this CA in their yum repository files for validating the Pulp server. The
problem is that the consumer must have already trusted Pulp in order to have registered to Pulp to
get this CA file, which helps the consumer to trust Pulp. It’s best for users to configure CA trust
themselves outside of Pulp, which is why this setting should not be used.
If you want to use SSL with Qpid, see the Qpid SSL Configuration Guide.
Turning off Validation¶
It is strongly recommended that you make or acquire signed certificates to prevent man-in-the-middle attacks or other nefarious activities. It is very risky to assume that the other end of the connection is who they claim to be. SSL uses a combination of encryption and authentication to ensure private communication. Disabling these settings removes the authentication component from the SSL session, which removes the guarantee of private communication since you can’t be sure who you are communicating with.
Pulp has a setting called
verify_ssl in these files:
you configure these settings to false, the respective Pulp components will no longer validate the
Pulp server’s certificate signature.
Pulp Broker Settings¶
To configure Pulp to work with a non-default broker configuration read the Pulp Broker Settings Guide.
To configure Pulp for connecting to the MongoDB with username/password authentication, use the following steps:
Configure MongoDB for username password authentication. See MongoDB - Enable Authentication for details.
/etc/pulp/server.conf, find the
[database]section and edit the
passwordvalues to match the user configured in step 1.
Restart all of Pulp’s services. For systemd:
$ sudo systemctl restart httpd pulp_workers pulp_resource_manager pulp_celerybeat
$ for s in httpd pulp_workers pulp_resource_manager pulp_celerybeat; do sudo service $s restart; done;
Pulp reads the log configuration during startup. If the log level is changed while Pulp is running, then you will need to restart it.
Pulp’s log type can be adjusted with the
log_type setting in the
[server] section of
/etc/pulp/server.conf. This setting is optional and defaults to syslog. Valid choices are
syslog and console.
Pulp’s log level can be adjusted with the
log_level setting in the
[server] section of
/etc/pulp/server.conf. This setting is optional and defaults to INFO. Valid choices are
CRITICAL, ERROR, WARNING, INFO, DEBUG, and NOTSET.
This setting will only adjust the verbosity of the messages that Pulp emits. If you wish to see all of these messages, you may also need to set the log level on your syslog handler. For example, rsyslog typically only displays INFO and higher, so if you set Pulp to DEBUG it will still be filtered by rsyslog. See the rsyslogd section for more information.
Pulp’s use of syslog is a departure from previous Pulp releases which used to write their own log files to /var/log/pulp/. This was problematic for Pulp’s 2.4.0 release as Pulp evolved to use a multi-process distributed architecture. Python’s file-based log handler cannot be used by multiple processes to write to the same file path, and so Pulp had to do something different. Syslog is a widely used logging protocol, and given the distributed nature of Pulp it was the most appropriate logging solution available.
Since Pulp is a multi-process application, Pulp will attempt to log a shortened 8 character version
of the task id if the log entry is emitted from a task process. This can be used to look up the task
pulp-admin tasks commands. An example of a log statement with a task id would be:
Jan 20 23:12:02 myhost pulp: pulp_rpm.plugins.importers.yum.sync:INFO: [338bdde4] Downloading 32 RPMs
Here the shortened task id is
338bdde4. The full task id would be
338bdde4-608a-44ab-a79c-49c28b0fe037. A statement without a task id would look like:
Jan 21 23:12:02 myhost pulp: pulp.server.async.worker_watcher:INFO: New worker 'resource_manager@myhost' discovered
Pulp has a maintenance job that deletes orphaned applicability profile data generated when using Pulp with consumers. This job runs monthly, but due to how Celery uses the periodic task feature, it only runs if the process stays running longer than 30 days. In environments where process restarts occur more frequently, it is recommended to configure a cron job to run the following script weekly or monthly:
celery -A pulp.server.async.app call pulp.server.maintenance.monthly.queue_monthly_maintenance
There is an rpm available that will install this command as a weekly cronjob named pulp-maintenance. Install it on one of your Pulp servers using:
sudo dnf install pulp-maintenance